DESCRIPTION Auxiliary
battery power is supplied to the BATT terminal of the hybrid vehicle
control ECU in order to store DTCs and freeze frame data. Even if the
power switch is turned off, back-up power is supplied. |
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
MIL | Warning Indicate | |
P056014 | System Voltage (BATT) Circuit Short to Ground or Open |
Malfunction in the hybrid vehicle control ECU back-up power source circuit
(1 trip detection logic) |
- Wire harness or connector
- Hybrid vehicle control ECU
- Fuse
| Comes on |
Master Warning Light: Comes on | MONITOR DESCRIPTION
If
a period of time has elapsed with a low voltage at the BATT terminal of
the hybrid vehicle control ECU, the hybrid vehicle control ECU will
determine that a malfunction has occurred in the back-up power supply
system, and it will store a DTC. The MIL will illuminate the next time
the power switch on (IG). MONITOR STRATEGY |
Related DTCs | P0562 (INF P056014): System voltage range check (Low voltage) | |
Required sensors/components | Main: Back-up power source circuit
Sub: Hybrid vehicle control ECU | |
Frequency of operation | Continuous | |
Duration | TMC's intellectual property | |
MIL operation | Immediately | |
Sequence of operation | None | TYPICAL ENABLING CONDITIONS |
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property | | Other conditions belong to TMC's intellectual property |
- | TYPICAL MALFUNCTION THRESHOLDS |
TMC's intellectual property |
- | COMPONENT OPERATING RANGE |
Auxiliary battery voltage | Between 9 and 14 V | CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the
vehicle has returned to normal by performing the following All Readiness
check procedure.
Click here 
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 5 seconds or more. [*1]
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
 CAUTION / NOTICE / HINT
NOTICE: After
turning the power switch off, waiting time may be required before
disconnecting the cable from the negative (-) auxiliary battery
terminal. Therefore, make sure to read the disconnecting the cable from
the negative (-) auxiliary battery terminal notices before proceeding
with work. Click here PROCEDURE
| 1. |
CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR) |
| (a)
Check the connector connections and contact pressure of the relevant
terminals for the hybrid vehicle control ECU connectors. Click here
OK: The connectors are connected securely and there are no contact pressure problems. |
|
| NG |
 | CONNECT SECURELY |
|
OK |
 | |
| 2. |
CHECK HARNESS AND CONNECTOR (POWER SOURCE OF HYBRID VEHICLE CONTROL ECU) |
(a) Turn the power switch off.
| (b) Measure the voltage according to the value(s) in the table below.
Standard Voltage: |
Tester Connection | Condition |
Specified Condition | |
G47-3 (BATT) - G46-6 (E1) |
Power switch off |
11 to 14 V | |
 |
|
*a | Component with harness connected
(Hybrid Vehicle Control ECU) | | |
| OK |
| REPLACE HYBRID VEHICLE CONTROL ECU |
|
NG | |
| |
| 3. |
CHECK FUSE (ECU-B NO. 4) |
| (a) Remove the ECU-B NO. 4 fuse from the fusible link block assembly. |
 |
|
*1 | Fusible Link Block Assembly | |
*2 | ECU-B NO. 4 Fuse | | |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
ECU-B NO. 4 fuse | Always |
Below 1 Ω | (c) Reinstall the ECU-B NO. 4 fuse.
| NG |
| REPLACE FUSE (ECU-B NO. 4) |
|
OK | |
| |
| 4. |
INSPECT FUSIBLE LINK BLOCK ASSEMBLY | (a) Disconnect the cable to the negative (-) auxiliary battery terminal.
(b) Disconnect the cable to the positive (+) auxiliary battery terminal.
| (c) Remove the fusible link block assembly. |
 |
|
*1 | Fusible Link Block Assembly | | |
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
A-1 (Positive (+) auxiliary battery terminal) - 7C-2 |
Always | Below 1 Ω |
(e) Reinstall the fusible link block assembly. (f) Reconnect the cable to the negative (-) auxiliary battery terminal.
(g) Reconnect the cable to the positive (+) auxiliary battery terminal.
| NG |
| REPLACE FUSIBLE LINK BLOCK ASSEMBLY |
|
OK | |
| |
| 5. |
CHECK HARNESS AND CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU) |
(a) Remove the ECU-B NO. 4 fuse from the fusible link block assembly. (b) Disconnect the G47 hybrid vehicle control ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
|
*1 | Fusible Link Block Assembly |
*2 | ECU-B NO. 4 Fuse Holder | |
*a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
Standard Resistance (Check for Open): |
Tester Connection | Condition |
Specified Condition | |
2 (ECU-B NO. 4 fuse holder) - G47-3 (BATT) |
Power switch off | Below 1 Ω |
Standard Resistance (Check for Short): |
Tester Connection | Condition |
Specified Condition | |
2 (ECU-B NO. 4 fuse) or G47-3 (BATT) - Body ground and other terminals |
Power switch off | 10 kΩ or higher |
(d) Reconnect the G47 hybrid vehicle control ECU connector. (e) Reinstall the ECU-B NO. 4 fuse.
| OK |
| REPLACE HYBRID VEHICLE CONTROL ECU |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR | | 
