Toyota Avalon Service & Repair Manual: Hybrid/EV Battery Block 1 Circuit Resistance Out of Range (Extreme) (P301100,...,P30211E)

Toyota Avalon Service & Repair Manual / Engine / Hybrid / Battery Control / Hybrid Control System / Hybrid/EV Battery Block 1 Circuit Resistance Out of Range (Extreme) (P301100,...,P30211E)

DESCRIPTION

Refer to the description for DTC P1AC000.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P301100

Hybrid/EV Battery Block 1 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30111E

Hybrid/EV Battery Block 1 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301200

Hybrid/EV Battery Block 2 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30121E

Hybrid/EV Battery Block 2 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301300

Hybrid/EV Battery Block 3 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30131E

Hybrid/EV Battery Block 3 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301400

Hybrid/EV Battery Block 4 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30141E

Hybrid/EV Battery Block 4 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301500

Hybrid/EV Battery Block 5 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30151E

Hybrid/EV Battery Block 5 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301600

Hybrid/EV Battery Block 6 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30161E

Hybrid/EV Battery Block 6 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301700

Hybrid/EV Battery Block 7 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30171E

Hybrid/EV Battery Block 7 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301800

Hybrid/EV Battery Block 8 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30181E

Hybrid/EV Battery Block 8 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P301900

Hybrid/EV Battery Block 9 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30191E

Hybrid/EV Battery Block 9 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P302000

Hybrid/EV Battery Block 10 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30201E

Hybrid/EV Battery Block 10 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P302100

Hybrid/EV Battery Block 11 Circuit Resistance Out of Range (Extreme)

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is extremely higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

P30211E

Hybrid/EV Battery Block 11 Circuit Resistance Out of Range

An internal malfunction of the HV battery is detected. The difference in the internal resistance of each battery block is higher than the specified value.

(1 trip detection logic)

  • HV battery
  • Hybrid battery terminal block
  • Battery voltage sensor

Comes on

Master Warning Light:

Comes on

HINT:

  • These DTCs can be stored after clearing DTCs and driving the vehicle for approximately 10 minutes.
  • These DTCs are stored when a malfunction is detected in the HV battery or a battery voltage sensor. However, depending on the driving conditions, the malfunction may not be reproduced if the condition of the HV battery changes.
    1. When the HV battery is malfunctioning:
      • - Voltage of 1 or more of the battery blocks has dropped.

        - Voltage of all battery blocks is output randomly with no certain pattern.

    2. When the battery voltage sensor is malfunctioning:
      • - While current is flowing to or from the HV battery, the voltage of a specific HV battery block will fluctuates.
  • In order to ensure HV battery performance, appropriate cooling performance must be maintained. Perform the following items as necessary. If cooling performance has decreased and "Maintenance Required for Traction Battery Cooling Parts See Owner's Manual" is displayed on the multi-information display, make sure to perform the following items:
    • Make sure the air intake port is not blocked.
    • Make sure there are no gaps between the connecting parts of the ducts.
    • Clean the No. 1 HV battery intake filter.
      • Clear the DTCs to reset the learning values even if no DTCs are stored.
Related Data List

DTC No.

Data List

P301100

  • Hybrid Battery Block 1 to 11 Voltage*1
  • Internal Resistance 1 to 11

P30111E

P301200

P30121E

P301300

P30131E

P301400

P30141E

P301500

P30151E

P301600

P30161E

P301700

P30171E

P301800

P30181E

P301900

P30191E

P302000

P30201E

P302100

P30211E

HINT:

  • *1: Under normal conditions, the values of Hybrid Battery Block 1, 2, 9, 10 and 11 Voltage will be approximately 16 V and Hybrid Battery Block 3, 4, 5, 6, 7 and 8 Voltage will be approximately 32 V.
  • If there is a short or open in a battery block voltage detection line, the value of Hybrid Battery Block Voltage for the corresponding battery block will be lower than 8 V.
  • The Data List items Internal Resistance 1 to 11 indicate internal resistance correction values used by the hybrid vehicle control ECU to detect malfunctions of the HV battery.

The following items can be helpful when performing repairs:

Data List
  • Ready Signal
  • Vehicle Speed
  • Accelerator Position
  • Shift Position
  • Engine Speed
  • Hybrid Battery Voltage
  • Hybrid Battery Current
  • BATT Voltage
  • Hybrid Battery SOC just after IG-ON
  • Hybrid Battery Maximum SOC
  • Hybrid Battery Minimum SOC
  • Total Distance Traveled
  • Distance from DTC Cleared
  • Engine Run Time
Vehicle Control History Data
  • Hybrid Battery Voltage Low

MONITOR DESCRIPTION

If there is an abnormal internal resistance or voltage in the battery blocks, the battery voltage sensor determines that a malfunction has occurred. When the malfunction detection condition is satisfied, the hybrid vehicle control ECU will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Related DTCs

P3011 (INF P301100/P30111E), P3012 (INF P301200/P30121E), P3013 (INF P301300/P30131E), P3014 (INF P301400/P30141E), P3015 (INF P301500/P30151E), P3016 (INF P301600/P30161E), P3017 (INF P301700/P30171E), P3018 (INF P301800/P30181E), P3019 (INF P301900/P30191E), P3020 (INF P302000/P30201E), P3021 (INF P302100/P30211E): Battery cell malfunction

Required sensors/components

Battery voltage sensor

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

Immediately

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Battery voltage sensor

DTC P3011 (INF P301100) is not detected

DTC P3011 (INF P30111E) is not detected

DTC P3012 (INF P301200) is not detected

DTC P3012 (INF P30121E) is not detected

DTC P3013 (INF P301300) is not detected

DTC P3013 (INF P30131E) is not detected

DTC P3014 (INF P301400) is not detected

DTC P3014 (INF P30141E) is not detected

DTC P3015 (INF P301500) is not detected

DTC P3015 (INF P30151E) is not detected

DTC P3016 (INF P301600) is not detected

DTC P3016 (INF P30161E) is not detected

DTC P3017 (INF P301700) is not detected

DTC P3017 (INF P30171E) is not detected

DTC P3018 (INF P301800) is not detected

DTC P3018 (INF P30181E) is not detected

DTC P3019 (INF P301900) is not detected

DTC P3019 (INF P30191E) is not detected

DTC P3020 (INF P302000) is not detected

DTC P3020 (INF P30201E) is not detected

DTC P3021 (INF P302100) is not detected

DTC P3021 (INF P30211E) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 2 minutes or more.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Drive the vehicle on urban roads for approximately 10 minutes.[*1]

    HINT:

    • This DTC may not be stored if the vehicle is stopped or being driven at a constant speed.
    • [*1]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

CAUTION:

  • Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
    • Inspecting the high-voltage system
    • Disconnecting the low voltage connector of the inverter with converter assembly
    • Disconnecting the low voltage connector of the HV battery
  • To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
  • After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    *a

    Without waiting for 10 minutes

    HINT:

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

  • Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

    If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

  • When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

    *a

    Dealer

    *b

    Battery Collection Agent

    • Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
  • After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE

1.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(d) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

P0AFC00, P0AFC96, P308A12 or P0AFC62 is not output.

A

P0AFC00, P0AFC96, P308A12 or P0AFC62 is output.

B

(e) Turn the power switch off.

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

A

2.

CHECK FREEZE FRAME DATA

Click here

Result

Proceed to

On the HV battery blocks 3 to 8, one of the conditions in the table above is met.

A

Other than above

B

B

GO TO STEP 5

A

3.

CHECK TOTAL DISTANCE DRIVEN

(a) Read the odometer to check the total distance the vehicle has been driven.

Result

Proceed to

Total distance driven is less than 200000 km (124280 mile)

A

Total distance driven is 200000 km (124280 mile) or more

Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1

Other than above

B

HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.

A

REPLACE HV BATTERY

B

4.

REPLACE HV BATTERY

Click here

NEXT

REPLACE HYBRID BATTERY TERMINAL BLOCK

5.

CHECK FREEZE FRAME DATA

Click here

Result

Proceed to

Either of the following conditions is met:

1. All conditions in table 1 are met.

2. All conditions in table 2 are met.

A

Other than above

B

A

REPLACE BATTERY VOLTAGE SENSOR

B

6.

READ VALUE USING TECHSTREAM (HYBRID BATTERY BLOCK VOLTAGE)

Click here

Result

Proceed to

All conditions in Table 1, Table 2 or Table 3 are met.

A

Other than above

B

A

REPLACE BATTERY VOLTAGE SENSOR

B

7.

CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(d) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

P1CFD1E, P302100 or P30211E is not output.

A

P1CFD1E, P302100 or P30211E is output.

B

(e) Turn the power switch off.

B

GO TO STEP 10

A

8.

CHECK TOTAL DISTANCE DRIVEN

(a) Read the odometer to check the total distance the vehicle has been driven.

Result

Proceed to

Total distance driven is less than 200000 km (124280 mile)

A

Total distance driven is 200000 km (124280 mile) or more

Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1

Other than above

B

HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.

A

REPLACE HV BATTERY

B

9.

REPLACE HV BATTERY

Click here

NEXT

REPLACE HYBRID BATTERY TERMINAL BLOCK

10.

REPLACE HV BATTERY

Click here

NEXT

REPLACE HYBRID BATTERY TERMINAL BLOCK

    High Voltage Power Resource Circuit Short during Pre-Charge (P300449)

    Lost Communication with Airbag System Control Module Circuit Short to Ground (P310711)

    See More:

    Toyota Avalon Service & Repair Manual > Meter / Gauge System(for Hv Model): System Description
    SYSTEM DESCRIPTION INPUT AND OUTPUT SIGNALS OF COMBINATION METER ASSEMBLY (a) Meter or Gauge Item Condition Input/Output Communication line Signal Component Speedometer Gauge Input CAN Vehicle speed (SP1) signal Skid control ECU (Brake booster with master cylinder assembly) - Output CAN Vehicle spee ...

    Toyota Avalon Owners Manual

    Toyota Avalon Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0158