INSPECTION PROCEDURE 1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)
(a) Check the mirror select switch and mirror surface adjust switch.
| (1) Turn the mirror select switch to the L position. |
 |
|
*a | Mirror Select and Surface Adjust Switch | |
*b | Component without harness connected
(Outer Mirror Switch Assembly) | | |
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for left side): |
Tester Connection | Condition |
Specified Condition | |
10 (VL) - 7 (B) 13 (M+) - 15 (E) |
Up | Below 2 Ω | |
Off | 10 kΩ or higher | |
10 (VL) - 15 (E) 13 (M+) - 7 (B) |
Down | Below 2 Ω | |
Off | 10 kΩ or higher | |
9 (HL) - 7 (B) 13 (M+) - 15 (E) |
Left | Below 2 Ω | |
Off | 10 kΩ or higher | |
9 (HL) - 15 (E) 13 (M+) - 7 (B) |
Right | Below 2 Ω | |
Off | 10 kΩ or higher |
(3) Turn the mirror select switch to the R position. (4) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for right side): |
Tester Connection | Condition |
Specified Condition | |
12 (VR) - 7 (B) 13 (M+) - 15 (E) |
Up | Below 2 Ω | |
Off | 10 kΩ or higher | |
12 (VR) - 15 (E) 13 (M+) - 7 (B) |
Down | Below 2 Ω | |
Off | 10 kΩ or higher | |
11 (HR) - 7 (B) 13 (M+) - 15 (E) |
Left | Below 2 Ω | |
Off | 10 kΩ or higher | |
11 (HR) - 15 (E) 13 (M+) - 7 (B) |
Right | Below 2 Ω | |
Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
(b) Check that the LED illuminates.
| (1) Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
OK: |
Auxiliary Battery Connection |
Specified Condition | |
Auxiliary battery positive (+) - 8 (ILL+) Auxiliary battery negative (-) - 14 (ILL-) |
LED illuminates | If the result is not as specified, replace the outer mirror switch assembly. |
 |
|
*a | Component without harness connected
(Outer Mirror Switch Assembly) | | |
2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory) (a) Check the mirror select switch and mirror surface adjust switch.
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
13 (M+) - 16 (E) |
Mirror surface adjust switch pushed up |
90 to 110 Ω | |
Mirror surface adjust switch pushed down |
437 to 503 Ω | |
Mirror surface adjust switch pushed left |
744 to 856 Ω | |
Mirror surface adjust switch pushed right |
225 to 275 Ω | |
Mirror surface adjust switch not pushed |
10 kΩ or higher | |
15 (MSW) - 16 (E) |
Mirror select switch turned to R position |
Below 10 Ω | |
Mirror select switch turned to L position |
90 to 110 Ω | |
Mirror select switch off |
10 kΩ or higher | If the result is not as specified, replace the outer mirror switch assembly. |
 |
|
*a | Mirror Select and Surface Adjust Switch | |
*b | Component without harness connected
(Outer Mirror Switch Assembly) | | |
(b) Check that the LED illuminates.
| (1) Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
OK: |
Auxiliary Battery Connection |
Specified Condition | |
Auxiliary battery positive (+) - 14 (ILL+) Auxiliary battery negative (-) - 12 (ILL-) |
LED illuminates | If the result is not as specified, replace the outer mirror switch assembly. |
 |
|
*a | Component without harness connected
(Outer Mirror Switch Assembly) | | | | 
