Toyota Avalon (XX50): Transmission Control Cable

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Drivetrain / Ua80e Automatic Transmission / Transaxle / Transmission Control Cable

Adjustment

ADJUSTMENT

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

Make sure to apply the parking brake and chock a wheel before performing this procedure.
If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. REMOVE CONSOLE BOX ASSEMBLY

Click here

3. ADJUST SHIFT LEVER POSITION

NOTICE:

Before adjusting the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.

(a) Disconnect the transmission control cable assembly from the transmission floor shift assembly.

(b) Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.

*a	Slider
*b	Lock Piece
*c	Slide
*d	Pull

NOTICE:

Check that the lock piece is pulled out.
Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.
Connect the transmission control cable assembly so that the lock piece faces the driver side.

*a	Lock Piece
*b	Adjuster Case

(d) Push the lock piece into the adjuster case.

NOTICE:

Check that the park/neutral position switch assembly and shift lever are in N.
Securely push in the lock piece until the slider lock is engaged.

*a	Lock Piece
*b	Push in
*c	Adjuster Case

(e) After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.

4. INSTALL CONSOLE BOX ASSEMBLY

Click here

Components

COMPONENTS

ILLUSTRATION

*1	BATTERY CLAMP SUB-ASSEMBLY	-	-
	Nm (kgfcm, ft.*lbf): Specified torque	-	-

ILLUSTRATION

*1	FRONT LOWER NO. 1 FLOOR HEAT INSULATOR	-	-
	Nm (kgfcm, ft.*lbf): Specified torque	-	-

ILLUSTRATION

*1	NO. 1 CONSOLE BOX DUCT	*2	TRANSMISSION CONTROL CABLE ASSEMBLY
	Nm (kgfcm, ft.*lbf): Specified torque	●	Non-reusable part

Installation

INSTALLATION

PROCEDURE

1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

(a) Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

(b) Connect the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

(d) Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.

*a	Correct
*b	Incorrect

2. INSTALL NO. 1 CONSOLE BOX DUCT

(a) Install the No. 1 console box duct.

3. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

Click here

4. INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

(a) Install the front lower No. 1 floor heat insulator to the vehicle body with the 2 nuts.

Torque:

4.9 N·m {50 kgf·cm, 43 in·lbf}

5. INSTALL FRONT EXHAUST PIPE ASSEMBLY

Click here

6. INSTALL BATTERY CLAMP SUB-ASSEMBLY

Click here

7. INSTALL ECM

Click here

8. INSTALL BATTERY

Click here

9. INSPECT SHIFT LEVER POSITION

Click here

10. ADJUST SHIFT LEVER POSITION

Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*1
		Lighting System (for Gasoline Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
Replacement of ECM	ECU communication ID registration (Immobiliser system)	Engine start function
Replacement of ECM (If transaxle compensation code read from ECM)	Perform reset memory*2 Transfer transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization for Registration
Replacement of ECM (If transaxle compensation code not read from ECM)	Perform reset memory*2 Reset transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization for Registration
Replacement of ECM	Code registration (Smart key System (for Start Function))	Wireless Door Lock Control System Smart Key System (for Entry Function) Smart Key System (for Start Function) Steering lock function

*1: When performing learning using the Techstream.
Click here
*2: Not necessary when ECM replaced with new one

PROCEDURE

1. REMOVE BATTERY

Click here

2. REMOVE ECM

Click here

3. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here

4. REMOVE FRONT EXHAUST PIPE ASSEMBLY

Click here

5. REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

(a) Remove the 2 nuts and front lower No. 1 floor heat insulator from the vehicle body.

6. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

Click here

7. REMOVE NO. 1 CONSOLE BOX DUCT

(a) Remove the No. 1 console box duct.

8. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

(a) While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.

*a	Clip
*b	45° to 60°

(b) Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.

(d) Remove the 2 nuts and then remove the transmission control cable assembly from the vehicle body.

Torque Converter And Drive Plate

Transmission Wire

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Audio / Video: Stereo Component Amplifier
Components COMPONENTS ILLUSTRATION *1 AUDIO AMPLIFIER COVER *2 STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET ILLUSTRATION *1 NO. 1 AMPLIFIER BRACKET *2 NO. 2 AMPLIFIER BRACKET *3 STEREO COMPONENT AMPLIFIER ASSEMBLY - - Installation INSTALLATION PROCEDURE 1. INSTALL STEREO COMPONENT AMPLIFIER ASSE ...