Toyota Avalon Service & Repair Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under Normal Condition are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Warm up the engine.

(b) Turn the A/C switch off.

(c) Turn the engine switch off.

(d) Connect the Techstream to the DLC3.

(e) Turn the engine switch on (IG).

(f) Turn the Techstream on.

(g) Enter the following menus: Powertrain / Engine / Data List.

(h) According to the display on the Techstream, read the Data List.

HINT:

Normal Condition: If no idling conditions are specified, the shift lever should be in N or P, and the A/C switch and all accessory switches should be off.

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Battery Voltage

Battery voltage

Min.: 0.0 V

Max.: 65.5 V

11 to 14 V: Idling

If the result is not as specified, abnormal battery voltage is suspected.

Alternator Output Duty Ratio

Generator output duty

Min.: 0.0%

Max.: 399.9%

Changes according to alternator output.

If the result is not as specified, a malfunction of the charging system is suspected.

Alternator Voltage - Non Active Test

Requested voltage when regulator forced drive is not executed

Min.: 0.000 V

Max.: 79.998 V

After engine start:

13.5 to 14.4 V (varies with generator temperature)

If the result is not as specified, a malfunction of the charging system is suspected.

Voltage of Alternator

Requested voltage when regulator under forced activation

Min.: 0.0 V

Max.: 79.9 V

After engine start:

Approximately same as requested output voltage when Active Test "Control the Voltage of Alternator" is performed

If the result is not as specified, a malfunction of the charging system is suspected.

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Powertrain > Engine > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Control the Voltage of Alternator

Requested output voltage of generator regulator during forced activation

Between 12.5 and 14.7 V

Test is possible after engine start

    Charging Failure

    Diagnosis System

    See More:

    Toyota Avalon Service & Repair Manual > Dynamic Radar Cruise Control System(for Hv Model): Terminals Of Ecu
    TERMINALS OF ECU CHECK DRIVING SUPPORT ECU ASSEMBLY NOTICE: Do not apply excessive force to the connector. If a force of 10 kg or more is applied, the connector may be broken. (a) Measure the voltage and resistance according to the value(s) in the table below. Terminal No. (Symbol) Wiring Color Term ...

    Toyota Avalon Owners Manual

    Toyota Avalon Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0155