Toyota Avalon Service & Repair Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Pre-Collision 2 > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Turn Light RH

Turn signal switch (right) status

ON or OFF

ON: Turn signal switch (right) on

OFF: Turn signal switch (right) off

-

Turn Light LH

Turn signal switch (left) status

ON or OFF

ON: Turn signal switch (left) on

OFF: Turn signal switch (left) off

-

PCS OFF Switch

Pre-collision system on/off status

ON or OFF

ON: Pre-collision system on

OFF: Pre-collision system off

-

Pre-Collision Safety Warning Buz

Pre-collision system warning buzzer

Valid or Inval

Valid: Pre-collision system warning buzzer operation possible

Inval: Pre-collision system warning buzzer operation not possible

-

Pre-Collision Brake

Pre-collision braking function

Valid or Inval

Valid: Pre-collision braking operation possible

Inval: Pre-collision braking operation not possible

-

PBA Start

Pre-collision brake assist activation signal

OFF, Standby, Assist Lv1 or Assist Lv2

OFF: Pre-collision brake assist not operating

Standby: Brake pedal not depressed during pre-collision brake assist operation

Assist Lv1: Brake pedal depressed during pre-collision brake assist operation

Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation

Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)

Warning Brake

-

-

-

Not applicable to the vehicle

Brake Assist Standby

-

-

-

This item is displayed on the Techstream but is not used.

Pre-Collision Brake Control

Pre-collision braking operational status

ON or OFF

ON: Pre-collision braking operating

OFF: Pre-collision braking not operating

-

AVS Start

-

-

-

This item is displayed on the Techstream but is not used.

VGRS Start

-

-

-

This item is displayed on the Techstream but is not used.

PBA Control

Pre-collision brake assist operational status

Valid or Invalid

Valid: Pre-collision brake assist control operation possible

Invalid: Pre-collision brake assist control operation not possible

-

Pre-Collision Safety Brake Ind

Pre-collision system alarm warning message status

ON or OFF

ON: Displayed

OFF: Not displayed

"BRAKE!" is displayed

PCS Crash Alarm Buzzer

PCS meter buzzer status

ON or OFF

ON: PCS meter buzzer sounding

OFF: PCS meter buzzer not sounding

-

Front Radar-Dirt History

Millimeter wave radar sensor assembly dirt history

ON or OFF

ON: History of excessive dirt

OFF: No history of excessive dirt

-

Front Radar-Temperature Malfunction History

Millimeter wave radar sensor assembly abnormal temperature history

ON or OFF

ON: History of abnormal temperature

OFF: No history of abnormal temperature

-

Front Radar-Low Voltage History

Millimeter wave radar sensor assembly low voltage history

ON or OFF

ON: History of low voltage

OFF: No history of low voltage

-

Front Radar-Incorrect Axial Gap (Vertical) History

Millimeter wave radar sensor assembly vertical misalignment history

ON or OFF

ON: History of vertical misalignment

OFF: No history of vertical misalignment

If "Pre-Collision System Unavailable." is displayed on the multi-information display and there is front beam axis misalignment (vertical) history, the millimeter wave radar sensor assembly may be performing beam axis alignment correction. In this case, perform Front Beam Axis Adjustment to return the system to normal.

Front Radar-Incorrect Axial Gap (Horizontal) History

Millimeter wave radar sensor assembly horizontal misalignment history

ON or OFF

ON: History of horizontal misalignment

OFF: No history of horizontal misalignment

-

Front Recognition Camera-Blockage History

Forward recognition camera obstruction history

ON or OFF

ON: History of being obstructed

OFF: No history of being obstructed

-

Front Recognition Camera-Malfunction History

Front camera system unavailable history

ON or OFF

ON: History of unavailable

OFF: No history of unavailable

-

Driving Support ECU Destination Variation No

Destination country for driving support computer

Destination Variation No or Not Available

Actual country code

-

Control Mode

ECU control mode status

Normal or Check Mode

Normal: Normal operation

Check Mode: Operating in Control Mode

-

PCS Operation State Retention Setting

PCS Operation State Retention Setting customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

PCS Alarm Activation Distance Retention Setting 1

PCS Alarm Activation Distance Retention Setting 1 customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

PCS Alarm Activation Distance Retention Setting 2

PCS Alarm Activation Distance Retention Setting 2 customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

PCS Alarm Activation Distance Retention Setting 3

PCS Alarm Activation Distance Retention Setting 3 customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

The Number of DTCs

Number of trouble codes

0 to 255

Number of DTCs will be displayed

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Pre-Collision 2 > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PCS Crash Alarm Buzzer

PCS meter buzzer

ON / OFF

Test possible with power switch on (IG), vehicle stopped

    Customize Parameters

    Diagnosis System

    See More:

    Toyota Avalon Service & Repair Manual > Occupant Classification System(for Gasoline Model): Initialization
    INITIALIZATION DESCRIPTION (a) Zero point of the occupant classification sensors may deviate in the following situations. To ensure sensor accuracy, be sure to perform Zero Point Calibration. The occupant detection ECU is replaced. HINT: As the zero point is not automatically stored in a new occupan ...

    Toyota Avalon Owners Manual

    Toyota Avalon Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0191