Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

CAUTION:

• Wear protective gloves. Sharp areas on the parts may injure your hands.
• Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

  Click here

  

CAUTION:

• Wear protective gloves. Sharp areas on the parts may injure your hands.
• Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

  Click here

  

HINT:

• Use the same procedure for the RH side and LH side.
• The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FKS:

Click here

for 2GR-FKS:

Click here

CAUTION:

• Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
• If an airbag deploys for any reason, it may cause a serious injury.

4. REMOVE SPARE WHEEL COVER ASSEMBLY (for Gasoline Model)

w/ Seat Heater System:

Click here

5. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (for Gasoline Model)

w/ Seat Heater System:

Click here

6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)

Click here

7. REMOVE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Click here

8. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Click here

9. REMOVE FRONT DOOR SCUFF PLATE

Click here

10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the front door opening trim weatherstrip.

11. REMOVE REAR DOOR SCUFF PLATE (for Gasoline Model)

Click here

12. REMOVE REAR DOOR SCUFF PLATE (for HV Model)

Click here

13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the rear door opening trim weatherstrip.

14. REMOVE LAP BELT OUTER ANCHOR COVER

(a) Disengage the 3 claws to remove the lap belt outer anchor cover.

15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.

16. REMOVE CENTER PILLAR LOWER GARNISH

Click here

17. REMOVE CENTER PILLAR UPPER GARNISH

Click here

18. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

(b) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector. HINT: Tape the screwdriver tip before use.

*a Protective Tape *b Locking Button *c Release

(c) Remove the 2 bolts.

(d) Disengage the 2 guides to remove the front seat outer belt assembly.

19. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.