Toyota Avalon Service & Repair Manual: Front Occupant Classification Sensor LH Collision Detection (B1785)

DESCRIPTION

DTC B1785 is stored when the occupant detection ECU receives a collision detection signal sent by the front occupant classification sensor LH in the case of an accident.

DTC B1785 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident did not occur.

If the vehicle was not in a collision, but the occupant detection ECU receives a collision detection signal and stores DTC B1785, the DTC can be cleared by performing zero point calibration. Therefore, if DTC B1785 is output, first perform zero point calibration.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B1785

Front Occupant Classification Sensor LH Collision Detection

  • Front occupant classification sensor LH sensed large load.
  • Separate type front seat cushion spring assembly RH malfunction

Front occupant classification sensor LH (Separate type front seat cushion spring assembly RH)*

  • *: The front occupant classification sensor LH is built into the separate type front seat cushion spring assembly RH.

CAUTION / NOTICE / HINT

NOTICE:

  • When this DTC is stored, repair of the malfunction indicated can only be performed by initializing the occupant detection ECU or replacing the separate type front seat cushion spring assembly RH. Do not replace the occupant detection ECU to repair the malfunction indicated by this DTC.

    If the occupant detection ECU is replaced, this DTC will not be output but the occupant detection system may not function properly.

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

HINT:

When DTC B165A is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1785 is output, perform troubleshooting for this DTC first.

PROCEDURE

1.

PERFORM ZERO POINT CALIBRATION

(a) Using the Techstream, perform Zero Point Calibration.

Click here

OK:

"Zero Point Calibration is complete." is displayed.

NG

GO TO STEP 5

OK

2.

CHECK DTC

(a) Turn the engine switch on (IG), and wait for at least 60 seconds.

(b) Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs

(c) Clear the DTCs stored in the airbag ECU assembly.

Body Electrical > SRS Airbag > Clear DTCs

(d) Turn the engine switch off.

(e) Turn the engine switch on (IG), and wait for at least 10 seconds.

(f) Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes

OK:

DTC B1785 is not output.

HINT:

Codes other than DTC B1785 may be output at this time, but they are not related to this check.

(g) Turn the engine switch off.

OK

END

NG

3.

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH

(a) Turn the engine switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

(c) Replace the separate type front seat cushion spring assembly RH.

Click here

(d) Connect the cable to the negative (-) battery terminal.

NEXT

4.

PERFORM ZERO POINT CALIBRATION

(a) Using the Techstream, perform Zero Point Calibration.

Click here

NEXT

END

5.

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH

(a) Turn the engine switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

(c) Replace the separate type front seat cushion spring assembly RH.

Click here

(d) Connect the cable to the negative (-) battery terminal.

NEXT

6.

PERFORM ZERO POINT CALIBRATION

(a) Using the Techstream, perform Zero Point Calibration.

Click here

NEXT

END

    Rear Occupant Classification Sensor LH Circuit Malfunction (B1782)

    Rear Occupant Classification Sensor LH Collision Detection (B1787)

    See More:

    Toyota Avalon Service & Repair Manual > Dynamic Radar Cruise Control System(for Hv Model): Operation Check
    OPERATION CHECK INPUT SIGNAL CHECK (a) Connect the Techstream to the DLC3. (b) Check the steering pad switch assembly using the Data List function of the Techstream (cruise control main switch, -SET switch, +RES switch and CANCEL switch). Click here *1 Steering Pad Switch Assembly *a Cruise Control ...

    Toyota Avalon Owners Manual

    Toyota Avalon Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.017