DESCRIPTION If additional
registration is not possible, a malfunction of the electrical key
transmitter sub-assembly, certification ECU (smart key ECU assembly),
engine switch, No. 1 indoor electrical key antenna assembly (front
floor), steering lock ECU (steering lock actuator or upper bracket
assembly) or door control receiver is suspected. CAUTION / NOTICE / HINT
NOTICE:
- If registration of an electrical key transmitter sub-assembly cannot be performed, refer to Registration.
Click here
- The smart key system (for Start Function, Gasoline Model) uses the LIN
communication system and CAN communication system. Inspect the
communication function by following How to Proceed with Troubleshooting.
Troubleshoot the smart key system (for Start Function, Gasoline Model)
after confirming that the communication systems are functioning
properly.
Click here
- When using the Techstream with the engine switch off, connect the
Techstream to the DLC3 and turn a courtesy light switch on and off at
intervals of 1.5 seconds or less until communication between the
Techstream and the vehicle begins. Then select the vehicle type under
manual mode and enter the following menus: Body Electrical / Smart Key.
While using the Techstream, periodically turn a courtesy light switch on
and off at intervals of 1.5 seconds or less to maintain communication
between the Techstream and the vehicle.
- Before replacing the certification ECU (smart key ECU assembly),
steering lock ECU (steering lock actuator or upper bracket assembly) or
electrical key transmitter sub-assembly, refer to Registration.
Click here
- After repair, confirm that no DTCs are output.
HINT: When additional registration is not possible, freeze frame data may be stored in the certification ECU (smart key ECU assembly).
If
freeze frame data is available, it can be helpful in determining
whether any parts were malfunctioning or not or narrowing down the
suspected areas based on the table below. Registration Function (Reason for Non-operation)
Parameter Name | Cause of Problem and Countermeasure |
Failed Registration Mode | Make sure that another mode or a different registration mode is not selected, and then perform registration again. |
Key Registration Max | Registration
was not possible because the maximum number of the electrical key
transmitter sub-assemblies has already been registered to the
certification ECU (smart key ECU assembly). If a new
electrical key transmitter sub-assembly needs to be registered, such as
when one of the registered electrical key transmitter sub-assemblies
has been lost, erase an unnecessary ID code first. |
Key Verification: Amp Abnormal | Although
a registered electrical key transmitter sub-assembly was held near the
engine switch, electrical key transmitter sub-assembly registration
could not be confirmed due to a malfunction of the immobiliser
amplifier, such as a short to ground. DTC B278A or B2784 was stored. |
Key Verification: Read Error | A
registered electrical key transmitter sub-assembly was not held near
the engine switch properly or electrical key transmitter sub-assembly
registration cannot be confirmed due to wave interference, etc. Register
the electrical key transmitter sub-assembly using the correct procedure
or use another registered electrical key transmitter sub-assembly. |
Transponder Key Amp Abnormal | Although
an unregistered electrical key transmitter sub-assembly was held near
the engine switch, electrical key transmitter sub-assembly registration
cannot be completed due to a malfunction of the immobiliser amplifier,
such as a short to ground. DTC B278A or B2784 was stored. |
New Key Registration Error | An
unregistered electrical key transmitter sub-assembly was not held near
the engine switch properly or electrical key transmitter sub-assembly
registration cannot be confirmed due to a malfunction, such as wave
interference. Reregister the electrical key
transmitter sub-assembly using the correct procedure or use another
registered electrical key transmitter sub-assembly. |
New Key Vehicle ID Error | Although
the vehicle ID stored in the certification ECU (smart key ECU assembly)
should be registered to the electrical key transmitter sub-assembly
during electrical key transmitter sub-assembly registration, it was not
successful. Use another unregistered electrical key transmitter sub-assembly for registration. |
New Key Registration Failed | Although
an unregistered electrical key transmitter sub-assembly was held near
the engine switch for registration, electrical key transmitter
sub-assembly registration was not successful due to wave interference
(such as radio waves emitted from a device in the cabin) or a low
transmitter battery. |
New Key Already Registered | As
a registered electrical key transmitter sub-assembly was held near the
engine switch by mistake, electrical key transmitter sub-assembly
registration was not successful. Using an unregistered electrical key transmitter sub-assembly, perform the registration procedure again. |
New Key ID Code Error | Replace the certification ECU (smart key ECU assembly). |
New Key Information Abnormal | The
ID code of an electrical key transmitter sub-assembly could not be
registered to the certification ECU (smart key ECU assembly). If 2
electrical key transmitter sub-assemblies are held near the engine
switch at the same time, incorrect registration information will be
stored in the certification ECU (smart key ECU assembly), suspending
registration. Reregister the electrical key transmitter sub-assembly using the correct registration procedure. | Body Electrical > Smart Key > Utility
Tester Display | Operation History | PROCEDURE
(a) Check for DTCs. Body Electrical > Smart Key > Trouble Codes
NOTICE: If a malfunction occurs, do not remove/install the vehicle battery before checking for DTCs.
OK: DTCs are not output.
NG | |
GO TO DIAGNOSTIC TROUBLE CODE CHART |
OK |
| |
2. |
READ VALUE USING TECHSTREAM (UNMATCHED VEHICLE-ID) |
(a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG)
(c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream. Body Electrical > Smart Key > Data List
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
Unmatched Vehicle-ID | Key No. (incorrect or correct) |
No or Yes | No: Communication normal
Yes: Communication malfunction |
The
vehicle ID registered in the vehicle and the vehicle ID registered in
the electrical key transmitter sub-assembly are different (if a key from
another vehicle is brought into the vehicle exterior detection area
while the doors are locked, "Yes" is displayed for "Unmatched
Vehicle-ID" in the Data List). Other potential causes:
- An electrical key transmitter sub-assembly from a different vehicle is being used.
- A communication error due to wave interference.
- The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
| Body Electrical > Smart Key > Data List
Tester Display | Unmatched Vehicle-ID |
Result | Proceed to |
"No" is displayed | A |
"Yes" is displayed | B |
B |
| GO TO STEP 5 |
A |
| |
3. |
CHECK SMART KEY SYSTEM (for Start Function, Gasoline Model) |
(a) Remove the transmitter battery from the electrical key transmitter sub-assembly.
(b)
With the brake pedal depressed, hold the electrical key transmitter
sub-assembly near the engine switch and check if the power source mode
changes. OK: The power source mode changes. HINT: If the power source mode changes, the cabin verification is malfunctioning. |
|
*1 | Engine Switch |
*2 | Electrical Key Transmitter Sub-assembly | | |
Result | Proceed to |
The power source mode changes |
A | The power source mode does not change |
B |
B |
| GO TO SMART KEY SYSTEM (for Start Function, Gasoline Model) (Power Source Mode does not Change to ON (IG and ACC)) |
A |
| |
4. |
CHECK STEERING LOCK FUNCTION | (a) The engine switch is on (ACC) or on (IG).
(b) Check that the steering unlocks.
HINT:
- When the engine switch is turned on (ACC) or on (IG) and the electrical
key transmitter assembly and certification ECU (smart key ECU assembly)
are verified, the steering is unlocked.
- Check that the communication between the steering lock ECU (steering
lock actuator or upper bracket assembly) and certification ECU (smart
key ECU assembly) is normal.
OK: The steering unlocks.
NG |
| GO TO SMART KEY SYSTEM (for Start Function, Gasoline Model) (Unable to Unlock Steering Wheel (Engine cannot Start)) |
OK |
| |
(a) Using an unregistered electrical key transmitter sub-assembly, perform the additional registration procedure.
Click here OK: Additional registration can be completed.
OK |
| REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (FIRST REGISTERED KEY WAS DEFECTIVE) |
NG |
| |
6. |
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
(a)
Temporarily replace the certification ECU (smart key ECU assembly) with
a new one and register the electrical key transmitter sub-assemblies.
HINT:
- For replacement.
Click here
- For registration.
Click here
OK: All
of the electrical key transmitter sub-assemblies could be registered to
the new certification ECU (smart key ECU assembly) successfully.
OK |
| END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) |
NG |
| GO TO OTHER PROBLEM (New key cannot be Registered) | |