Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: BSM Buzzer Malfunction (C2A5D)

DESCRIPTION

This DTC is stored when the television camera assembly receives an RCTA buzzer circuit malfunction signal from the blind spot monitor sensor RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

C2A5D

BSM Buzzer Malfunction

The RCTA buzzer circuit is abnormal.

  • Blind spot monitor system
  • Television camera assembly

Television camera assembly

CAUTION / NOTICE / HINT

NOTICE:

  • When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

    Click here

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

    Click here

PROCEDURE

1.

READ VALUE USING TECHSTREAM (BLIND SPOT MONITOR SENSOR LH STATUS)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Blind Spot Monitor Slave / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Blind Spot Monitor Slave > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Buzzer Connection

Status of the buzzer connection

Valid or Invalid

Valid: Buzzer connection is valid

Invalid: Buzzer connection is invalid

-

Slave Side RCTA Function

Switches the RCTA function on and off

OFF or ON

OFF: RCTA function off

ON: RCTA function on

-

Body Electrical > Blind Spot Monitor Slave > Data List

Tester Display

Buzzer Connection

Slave Side RCTA Function

Result

Proceed to

"Valid" and "ON" is displayed for all items.

A

"Invalid" or "OFF" is displayed.

B

B

GO TO BLIND SPOT MONITOR SYSTEM (PROBLEM SYMPTOMS TABLE)

A

2.

CHECK FOR DTC

(a) Clear the DTCs.

Chassis > Parking Assist Camera > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Chassis > Parking Assist Camera > Trouble Codes

Result

Proceed to

DTC C2A5D is output

A

DTC C2A5D is not output

B

B

REPLACE TELEVISION CAMERA ASSEMBLY

A

3.

CHECK FOR DTC (BLIND SPOT MONITOR SYSTEM (C1ABE))

(a) Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes

Result

Proceed to

DTC C1ABE is output

A

DTC C1ABE is not output

B

A

GO TO DIAGNOSTIC TROUBLE CODE CHART (C1ABE)

B

GO TO BLIND SPOT MONITOR SYSTEM (PROBLEM SYMPTOMS TABLE)

    BSM Buzzer Sound Request Signal Malfunction (C2A5C)

    Back Camera Response Malfunction (C2A6A)

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Front Seat Side Airbag Assembly: Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL FRONT SEAT AIRBAG ASSEMBLY (a) Install the front seat airbag assembly with 2 new nuts. Torque: 8.0 N·m {82 kgf·cm, 71 in·lbf} NOTICE: Do ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0166