Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Brake Switch "A" Signal Compare Failure (P057162)

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Engine / Cruise Control / Dynamic Radar Cruise Control System(for Hv Model) / Brake Switch "A" Signal Compare Failure (P057162)

DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake is applied, voltage is normally applied to the terminal STP of the hybrid vehicle control ECU through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU turns the dynamic radar cruise control system off.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

P057162

Brake Switch "A" Signal Compare Failure

While the power switch is on (IG) and the dynamic radar cruise control system is operating, voltage of the STP terminal and that of the ST1- terminal of the hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.
  • Stop light switch assembly
  • Harness or connector
  • Hybrid vehicle control ECU

Does not come on

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the hybrid vehicle control ECU, refer to Registration.

    Click here

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

(a) Disconnect the A33 stop light switch assembly connector.

*a

Front view of wire harness connector

(to Stop Light Switch Assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A33-2 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A33-7 (B) - Body ground

Always

11 to 14 V

A33-6 (B) - Body ground

Power switch on (IG)

11 to 14 V

A33-6 (B) - Body ground

Power switch off

Below 1 V

(d) Connect the A33 stop light switch assembly connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

2.

INSPECT STOP LIGHT SWITCH ASSEMBLY

(a) Inspect the stop light switch assembly.

Click here

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

OK

3.

CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect the A23 and A24 hybrid vehicle control ECU connectors.

(b) Disconnect the A33 stop light switch assembly connector.

(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.

(d) Disconnect the K10 certification ECU (smart key ECU assembly) connector.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A24-28 (ST1-) - A33-5 (L)

Always

Below 1 Ω

A23-15 (STP) - A33-3 (L)

Always

Below 1 Ω

A24-28 (ST1-) or A33-5 (L) - Body ground

Always

10 kΩ or higher

A23-15 (STP) or A33-3 (L) - Body ground

Always

10 kΩ or higher

(f) Connect the K10 certification ECU (smart key ECU assembly) connector.

(g) Connect the A35 skid control ECU (brake booster with master cylinder assembly) connector.

(h) Connect the A33 stop light switch assembly connector.

(i) Connect the A23 and A24 hybrid vehicle control ECU connectors.

OK

REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
    Brake Switch "A" Circuit Open (P057113)

    Cruise Control System Internal Failure (P057504,P057549)

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Rear Brake: Reassembly
    REASSEMBLY CAUTION / NOTICE / HINT CAUTION: If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly. for Gasoline Model: Click here for HV Model: Click here NOTICE: Make sure not to scratch, damage or apply excessive force to any ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.026