Toyota Avalon Service & Repair Manual: Illumination Circuit

Toyota Avalon Service & Repair Manual / Audio, Visual, Telematics / Audio / Video / Audio And Visual System(for Gasoline Model) / Illumination Circuit

DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click here
Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.	CHECK ILLUMINATION

(a) Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result	Proceed to
Illumination comes on for all components except steering pad switch assembly.	A
Illumination comes on for all components except radio and display receiver assembly.	B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.).	C

GO TO STEP 5

GO TO LIGHTING SYSTEM

2.	CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

(a) Disconnect the G17 spiral cable sub-assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
G17-14 (IL+2) - Body ground	Light control switch in tail or head position	11 to 14 V

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.	INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Inspect the steering pad switch assembly.

Click here

REPLACE STEERING PAD SWITCH ASSEMBLY

4.	INSPECT SPIRAL CABLE SUB-ASSEMBLY

(a) Remove the spiral cable sub-assembly.

Click here

(b) Inspect the spiral cable sub-assembly.

Click here

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY, COMBINATION METER ASSEMBLY)

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.	CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

(a) Disconnect the G2 radio and display receiver assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
G2-15 (ILL+) - Body ground	Light control switch in tail or head position	11 to 14 V

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.	CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the G2 radio and display receiver assembly connector.

(b) Disconnect the G16 combination meter assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
G2-16 (ILL-) - G16-1 (ILL-)	Always	Below 1 Ω
G2-16 (ILL-) or G16-1 (ILL-) - Body ground	Always	10 kΩ or higher

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

REPAIR OR REPLACE HARNESS OR CONNECTOR

How To Proceed With Troubleshooting

Illumination for Panel Switch does not Come on with Tail Switch ON

See More:

Toyota Avalon Owners Manual > Steps to take in an emergency: If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or commercial towing service, using a wheel-lift type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/ provincial and local laws. Situations when it is necessary to contact ...