Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Open in Bus 5 Main Bus Line

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Power Source, Network / Networking / Can Communication System(for Gasoline Model) / Open in Bus 5 Main Bus Line

DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom

Trouble Area

Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
  • CAN main bus lines or connector
  • Central gateway ECU (network gateway ECU)
  • Combination meter assembly
  • No. 3 CAN junction connector
  • No. 6 CAN junction connector
  • No. 2 junction connector
  • No. 3 junction connector

This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the K65 No. 6 CAN junction connector.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness connector

(to No. 6 CAN Junction Connector)

*b

to Central Gateway ECU (Network Gateway ECU)

*c

to No. 2 Junction Connector

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

K65-1 (CANH) - K65-12 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

Central gateway ECU (network gateway ECU)

K65-2 (CANH) - K65-13 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

No. 2 junction connector

Result

Proceed to

OK

A

NG (Line to central gateway ECU (network gateway ECU))

B

NG (Line to No. 2 junction connector)

C
A

REPLACE NO. 6 CAN JUNCTION CONNECTOR
C

GO TO STEP 3

B

2.

CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

(a) Reconnect the K65 No. 6 CAN junction connector.

(b) Disconnect the G52 central gateway ECU (network gateway ECU) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G52-15 (CA5H) - G52-16 (CA5L)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

*a

Front view of wire harness connector

(to Central Gateway ECU (Network Gateway ECU))
OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

3.

CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 JUNCTION CONNECTOR)

(a) Reconnect the K65 No. 6 CAN junction connector.

(b) Disconnect the K69 No. 2 junction connector.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness connector

(to No. 2 Junction Connector)

*b

to No. 6 CAN Junction Connector

*c

to No. 3 Junction Connector

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

K69-1 (CANH) - K69-12 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

No. 6 CAN junction connector

K69-2 (CANH) - K69-13 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

No. 3 junction connector

Result

Proceed to

OK

A

NG (Line to No. 6 CAN junction connector)

B

NG (Line to No. 3 junction connector)

C
A

REPLACE NO. 2 JUNCTION CONNECTOR
B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)
C

4.

CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 3 JUNCTION CONNECTOR)

(a) Reconnect the K69 No. 2 junction connector.

(b) Disconnect the K64 No. 3 junction connector.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness connector

(to No. 3 Junction Connector)

*b

to No. 3 CAN Junction Connector

*c

to No. 2 Junction Connector

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

K64-3 (CANH) - K64-14 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

No. 3 CAN junction connector

K64-4 (CANH) - K64-15 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

No. 2 junction connector

Result

Proceed to

OK

A

NG (Line to No. 3 CAN junction connector)

B

NG (Line to No. 2 junction connector)

C
A

REPLACE NO. 3 JUNCTION CONNECTOR
C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
B

5.

CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)

(a) Reconnect the K64 No. 3 junction connector.

(b) Disconnect the G94 No. 3 CAN junction connector.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness connector

(to No. 3 CAN Junction Connector)

*b

to No. 3 Junction Connector

*c

to Combination Meter Assembly

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

G94-3 (CANH) - G94-14 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

No. 3 junction connector

G94-5 (CANH) - G94-16 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

Combination meter assembly

Result

Proceed to

OK

A

NG (Line to No. 3 junction connector)

B

NG (Line to combination meter assembly)

C
A

REPLACE NO. 3 CAN JUNCTION CONNECTOR
B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
C

6.

CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

(a) Reconnect the G94 No. 3 CAN junction connector.

(b) Disconnect the G16 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G16-32 (CANH) - G16-31 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

*a

Front view of wire harness connector

(to Combination Meter Assembly)
OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)
    Open in Bus 4 Main Bus Line

    Open in One Side of Bus 1 Branch Line

    See More:

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Electric Parking Brake System(for Hv Model): Dtc Check / Clear
    DTC CHECK / CLEAR CHECK DTC AND FREEZE FRAME DATA (USING TECHSTREAM) (a) Turn the power switch off. (b) Connect the Techstream to the DLC3. (c) Turn the power switch on (IG). (d) Turn the Techstream on. (e) Enter the following menus: Chassis / Electric Parking Brake / Trouble Codes. Chassis > Ele ...

    Toyota Avalon (XX50) 2019-2022 Owners Manual

    Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0269