Toyota Avalon Service & Repair Manual: Operation Check

OPERATION CHECK

AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK

NOTICE:

Make sure that the customize settings are set to default when performing the automatic light control system operation check.

Click here

(a) Turn the engine switch on (IG).

(b) Turn the light control switch to the AUTO position.

(c) Cover the automatic light control sensor.

(d) Check that the taillights and low beam headlights come on.

(e) Uncover the automatic light control sensor.

(f) Check that the low beam headlights and taillights turn off.

LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK

NOTICE:

Make sure that the customize settings are set to default when performing the light auto turn-off system operation check.

Click here

(a) When the taillights are on (low beam headlights are not on)

(1) Close all of the doors.

(2) Turn the engine switch on (IG).

(3) Turn the taillights on.

(4) Turn the engine switch off.

(5) Open the driver door.

(6) Check that all of the lights turn off immediately.

(b) When the low beam headlights are on

(1) Close all of the doors.

(2) Turn the engine switch on (IG).

(3) Turn the low beam headlights on.

(4) Turn the engine switch off.

(5) Open any of the doors.

(6) Close the door.

(7) Check that all of the lights turn off after 30 seconds (delay function).

HINT:

Before the lights turn off, if the lock button on the key is pushed after all of the doors are locked, all of the lights will turn off immediately.

DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK

NOTICE:

Make sure that the customize settings are set to default when performing the daytime running light system operation check.

Click here

(a) Start the engine.

(b) Turn the light control switch to the tail or AUTO position (with the low beam headlights not turned on via the automatic light control system).

(c) Release the parking brake.

(d) Check that the daytime running lights come on.

NOTICE:

Make sure that the customize settings are set to default when performing the wiper-linked low beam headlight control system operation check.

Click here

WIPER-LINKED LOW BEAM HEADLIGHT CONTROL SYSTEM OPERATION CHECK

(a) Turn the engine switch on (IG).

(b) Shine a light on the automatic light control sensor.*

HINT:

*: If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.

(c) Turn the light control switch to the AUTO position.

(d) Operate the front wipers for 10 seconds or more (except MIST or washer-linked wiper operation) and check that the low beam headlights*1 or high beam headlights*2 illuminate.

  • *1: Dimmer switch high position
  • *2: Dimmer switch not high position

WELCOME LIGHT ILLUMINATION CONTROL OPERATION CHECK

NOTICE:

  • When operation of the alarm memory function is requested, welcome light illumination control will not operate.
  • Make sure that the customize settings are set to their default when performing the welcome light illumination control operation check.

    Click here

(a) Turn the engine switch off.

(b) Turn the light control switch to the AUTO position.

(c) Cover the automatic light control sensor.

(d) Close and lock all of the doors.

(e) Unlock all of the doors using the wireless door unlock or entry door unlock function.

(f) Check that the taillights, parking lights, front side marker lights and license plate lights illuminate for 15 seconds.

CORNERING LIGHT CONTROL OPERATION CHECK

(a) Turn the engine switch on (IG).

(b) Turn the light control switch to the head position.

(c) Perform the following operations while driving the vehicle at 150 km/h (93 mph) or less and check that the cornering lights operate appropriately.

  • Operate the left turn signal switch and check that the cornering light LH illuminates.*
  • Operate the right turn signal switch and check that the cornering light RH illuminates.*
  • Turn the steering wheel 25 degrees or more to the left and check that the cornering light LH illuminates. Turn the steering wheel to an angle of 10 degrees or less and check that the cornering light LH turns off.*
  • Turn the steering wheel 25 degrees or more to the right and check that the cornering light RH illuminates. Turn the steering wheel to an angle of 10 degrees or less and check that the cornering light RH turns off.*
  • Move the shift lever to R and check that the cornering light LH and cornering light RH illuminate.

NOTICE:

When disconnecting the cable from the battery terminal, if the steering angle sensor steering neutral point is not stored, the cornering lights may not operate as listed above in *. When disconnecting the cable from the battery terminal, perform the confirmation driving pattern to store the steering angle sensor steering neutral point.

Click here

*a

Automatic High Beam Indicator Light on Combination Meter Assembly

*b

Auto High Beam Switch Indicator

AUTOMATIC HIGH BEAM SYSTEM OPERATION CHECK

(a) Check the operation of the automatic high beam indicator light.

(1) Turn the engine switch on (IG).

(2) Turn the light control switch to the AUTO or head position.

(3) Move the dimmer switch to the high position.

(4) Press the auto high beam switch (indicator illuminates).

HINT:

If the auto high beam switch is turned on when the light control switch is not in the AUTO or head position, or the dimmer switch is not in the high position, "Auto High Beam Ready Turn ON High Beam to Activate" will be displayed on the multi-information display.

(5) Check that the automatic high beam indicator illuminates.

NOTICE:

When the forward recognition camera cannot correctly detect objects due to inclement weather such as thick fog or other visual obstructions, the automatic high beam indicator may not turn on and consequently the automatic high beam system may not operate.

(b) Check the operation of the automatic high beam function.

(1) At night, when driving the vehicle with the automatic high beam system in standby mode, check that the high beams automatically turn on after a short delay when all of the following conditions are met:

  • The vehicle speed is more than approximately 34 km/h (21 mph).
  • The area in front of the vehicle is dark.
  • There are no oncoming vehicles with headlights on.
  • There are no preceding vehicles with taillights on.
  • There are few streetlights along the street ahead.

(2) At night, when driving the vehicle with the high beams turned on by the automatic high beam system, check that the automatic high beam system turns off the high beams and returns to standby mode when any of the following conditions are met:

  • The vehicle speed is less than approximately 27 km/h (17 mph).
  • The level of ambient light is higher than a specified threshold.
  • There are oncoming vehicles with headlights on.
  • There are preceding vehicles with taillights on.
  • Light from streetlights ahead is higher than a specified threshold.
    Initialization

    Parking Light/Daytime Running Light Circuit

    See More:

    Toyota Avalon Service & Repair Manual > Motor Generator Control System: Dtc Check / Clear
    DTC CHECK / CLEAR CHECK FOR DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Motor Generator / Trouble Codes. Powertrain > Motor Generator > Trouble Codes (e) Check the DTCs and freeze frame d ...

    Toyota Avalon Owners Manual

    Toyota Avalon Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.023