Toyota Avalon Service & Repair Manual: No. 2 Clearance Warning Buzzer Circuit

DESCRIPTION

This circuit consists of the No. 2 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM (REAR BUZZER)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Active Test.

(e) Check that the rear buzzer operates by performing the Active Test.

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Rear Buzzer

No. 2 clearance warning buzzer

Stop or Operate

Confirm that the vehicle is stopped and the engine switch is on (IG)

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Active Test

Tester Display

Rear Buzzer

OK:

The No. 2 clearance warning buzzer sounds.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.

CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)

(a) Disconnect the K34 clearance warning ECU assembly connector.

(b) Disconnect the K27 No. 2 clearance warning buzzer connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K34-15 (BBZ) - K27-1 (Z+)

Always

Below 1 Ω

K34-16 (ER) - K27-2 (Z-)

Always

Below 1 Ω

K34-15 (BBZ) or K27-1 (Z+) - Body ground

Always

10 kΩ or higher

K34-16 (ER) or K27-2 (Z-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

REPLACE NO. 2 CLEARANCE WARNING BUZZER

(a) Replace the No. 2 clearance warning buzzer with a new or known good one.

Click here

NEXT

4.

PERFORM ACTIVE TEST USING TECHSTREAM (REAR BUZZER)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Active Test.

(e) Check that the rear buzzer operates by performing the Active Test.

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Rear Buzzer

No. 2 clearance warning buzzer

Stop or Operate

Confirm that the vehicle is stopped and the engine switch is on (IG)

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Active Test

Tester Display

Rear Buzzer

OK:

The No. 2 clearance warning buzzer sounds.

OK

END (NO. 2 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG

REPLACE CLEARANCE WARNING ECU ASSEMBLY

    No. 1 Clearance Warning Buzzer Circuit

    Operation Check

    See More:

    Toyota Avalon Service & Repair Manual > Adaptive Variable Suspension System: Test Mode Procedure
    TEST MODE PROCEDURE TEST MODE PROCEDURE NOTICE: After replacing the absorber control ECU, it is necessary to perform registration of vehicle identification information. Vehicle identification information is automatically acquired when the system enters test mode. HINT: When entering test mode, the a ...

    Toyota Avalon Owners Manual

    Toyota Avalon Service & Repair Manual

    © 2024 Copyright www.tavalon.net
    0.0186