DESCRIPTION When the
wireless operation can be used to lock and unlock the doors,
communication between the electrical key and tire pressure monitoring
system receiver assembly and certification ECU (smart key ECU assembly)
is normal. If the entry lock and unlock functions do not operate, the
entry cancel function may be set through the customize function, there
may be communication problems between the electrical key transmitter
sub-assembly and vehicle, or there may be wave interference. CAUTION / NOTICE / HINT
NOTICE:
- The smart key system (for Entry Function, Gasoline Model) uses the CAN
communication system. Inspect the communication function by following
How to Proceed with Troubleshooting. Troubleshoot the smart key system
(for Entry Function, Gasoline Model) after confirming that the
communication systems are functioning properly.
Click here
- When using the Techstream with the engine switch off, connect the
Techstream to the DLC3 and turn a courtesy light switch on and off at
intervals of 1.5 seconds or less until communication between the
Techstream and the vehicle begins. Then select the vehicle type under
manual mode and enter the following menus: Body Electrical / Smart Key.
While using the Techstream, periodically turn a courtesy light switch on
and off at intervals of 1.5 seconds or less to maintain communication
between the Techstream and the vehicle.
- Check that there are no electrical key transmitter sub-assemblies in the vehicle.
- Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
Click here
- Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Precaution.
Click here
- After repair, confirm that no DTCs are output.
PROCEDURE
1. | CHECK POWER DOOR LOCK CONTROL SYSTEM |
(a)
When the door control switch on the multiplex network master switch
assembly is operated, check that the doors unlock and lock according to
the switch operation. Click here OK:
Door locks operate normally.
NG | |
GO TO POWER DOOR LOCK CONTROL SYSTEM (for Gasoline Model) |
OK |
| |
2. |
CHECK WAVE ENVIRONMENT | (a) Move the electrical key transmitter sub-assembly as described below and perform the operation inspection.
HINT:
- When the electrical key transmitter sub-assembly is brought near the
front door outside handle assembly (for driver door) or electrical key
antenna (outside luggage compartment), the possibility of wave
interference decreases, and it can be determined if wave interference is
causing the problem symptom.
- If the inspection result is that the problem only occurs in certain
locations or at certain times of day, the possibility of wave
interference is high. Also, added vehicle components may cause wave
interference. If installed, remove them and perform the operation check.
- There may be wave interference if the vehicle is near broadcasting
antennas, large video displays, wireless garage door opener systems,
wireless security cameras, home security systems, etc. In this case,
move the vehicle to a different location and check if there is any
improvement.
- If a tool for checking radio waves, such as a signal strength meter, is
available, move around the area while observing both the LF band (used
by the vehicle antenna to form the detection area) and RF band (used by
the electrical key transmitter sub-assembly for transmission) to check
for locations where there is wave interference.
- The transmitting wave of the wireless function and entry function are
the same, but the wave logic is different. As a result, it is possible
that only the wireless function or only the entry function is affected
by wave interference.
(1)
Bring the electrical key transmitter sub-assembly approximately 0.3 m
(0.984 ft.) from the front door outside handle assembly (for driver
door) and perform a driver door entry lock and unlock operation check. HINT:
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door handle. |
|
*a | Approximately 0.3 m (0.984 ft.) | | |
(2)
Bring the electrical key transmitter sub-assembly approximately 0.3 m
(0.984 ft.) from the front door outside handle assembly (for front
passenger door) and perform a front passenger door entry lock and unlock
operation check. HINT: Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door handle. |
|
*a | Approximately 0.3 m (0.984 ft.) | | |
(3)
Bring the electrical key transmitter sub-assembly approximately 0.3 m
(0.984 ft.) from the electrical key antenna (outside luggage
compartment) and perform an entry luggage compartment door open function
check. HINT: Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear bumper. |
|
*a | Approximately 0.3 m (0.984 ft.) | | |
Result | Proceed to |
All operation checks fail |
A | All operation checks are normal |
B | Some operation checks are normal |
C |
B |
| AFFECTED BY WAVE INTERFERENCE |
C |
| GO TO OTHER PROBLEM |
A |
| |
3. |
CHECK KEY DIAGNOSTIC MODE | (a) Check the following antennas in key diagnostic mode. Body Electrical > Smart Key > Utility
Tester Display | Communication Check(Key Diag Mode) |
(b) Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.
(1) Check the electrical key antenna (for driver door): When
the electrical key transmitter sub-assembly is brought within 0.7 to 1 m
(2.30 to 3.28 ft.) of the front door outside handle assembly (for
driver door), check that the wireless buzzer sounds.
HINT:
- Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
- If the buzzer sounds with [CH1] displayed but not with [CH2], the
electrical key transmitter sub-assembly cannot be detected by channel 2
due to a malfunction, such as wave interference.
|
|
*a | 0.7 to 1 m (2.30 to 3.28 ft.) | | |
(2) Check the electrical key antenna (for front passenger door):
When
the electrical key transmitter sub-assembly is brought within 0.7 to 1 m
(2.30 to 3.28 ft.) of the front door outside handle assembly (for front
passenger door), check that the wireless buzzer sounds.
HINT:
- Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
- If the buzzer sounds with [CH1] displayed but not with [CH2], the
electrical key transmitter sub-assembly cannot be detected by channel 2
due to a malfunction, such as wave interference.
|
|
*a | 0.7 to 1 m (2.30 to 3.28 ft.) | | |
(3) Check the electrical key antenna (outside luggage compartment):
When
the electrical key transmitter sub-assembly is brought within 0.7 to 1 m
(2.30 to 3.28 ft.) of the electrical key antenna (outside luggage
compartment), check that the wireless buzzer sounds.
HINT:
- Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
- If the buzzer sounds with [CH1] displayed but not with [CH2], the
electrical key transmitter sub-assembly cannot be detected by channel 2
due to a malfunction, such as wave interference.
OK: Wireless buzzer sounds. |
|
*a | 0.7 to 1 m (2.30 to 3.28 ft.) | | |
Result | Proceed to |
All diagnostic mode inspections fail |
A | Some diagnostic mode inspections fail (door) |
B | Some diagnostic mode inspections fail (outside luggage compartment) |
C | All diagnostic mode inspections are normal |
D |
B |
| GO TO OTHER PROBLEM |
C |
| GO TO OTHER PROBLEM |
D |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
A |
| |
4. |
CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY |
(a) Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
Result | Proceed to |
Another registered electrical key transmitter sub-assembly is not available |
A | Another registered electrical key transmitter sub-assembly is available |
B |
B |
| GO TO STEP 6 |
A |
| |
5. |
ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY) |
(a) Register a new electrical key transmitter sub-assembly. Click here
NEXT |
| |
6. |
CHECK ENTRY LOCK OPERATION | (a) Using another registered electrical key transmitter sub-assembly, check that the entry function operates normally.
Click here
Result | Proceed to |
Entry function operates normally |
A | Entry function does not operate normally |
B |
A |
| END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE) |
B |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) | |