Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Customize Parameters

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Audio, Visual, Telematics / Park Assist / Monitoring / Intuitive Parking Assist System(for Gasoline Model) / Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM

(a) Customizing with the Techstream.

NOTICE:

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch on (IG).

(3) Turn the intuitive parking assist system on.

(4) Turn the Techstream on.

(5) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Utility / Customize Setting.

(6) Select the setting by referring to the table below.

Warning

Tester Display	Description	Default	Setting	ECU
Fr Corner Sensor Onset Range	Sets the detection operation range for the front corner sensors.	Long	0:Short,1:Long	Clearance warning ECU assembly
Rr Corner Sensor Onset Range	Sets the detection operation range for the front corner sensors.	Long	0:Short,1:Long	Clearance warning ECU assembly
Fr Sensor Onset Range	Sets the detection operation range for the front center sensors.	Wide	0:Narrow,1:Wide	Clearance warning ECU assembly
Rr Sensor Onset Range	Sets the detection operation range for the rear center sensors.	Wide	0:Narrow,1:Wide	Clearance warning ECU assembly
Keep Sense Buzzer	Sets whether the buzzer stops sounding when the distance between the vehicle and a detected object does not change for 3 seconds.	Avail	0:Not Avail,1:Avail	Clearance warning ECU assembly
Fr & Rr Buzzer Volume	Changes the buzzer volume setting.	M2	001:L,010:M1,011:M2,100:M3,101:H	Clearance warning ECU assembly
Object Not Moving 3s Buzz Vol	Sets the volume at which the buzzer sounds when the distance between the vehicle and a detected object does not change for 3 seconds.	Keep	00:Keep Vol,01:L,10:M1,11:M2	Clearance warning ECU assembly
Leave Buzzer Volume	Sets the volume of the buzzer with respect to the distance between the vehicle and a detected object.	L	00:Keep Vol,01:L,10:M1,11:M2	Clearance warning ECU assembly
Temporary Mute Reset Speed Adjust	Sets the vehicle speed at which the temporary mute function resets.	20 km/h	00:System Link,01:15km/h,10:20km/h,11:30km/h	Clearance warning ECU assembly
Temporary Mute Function	Sets the availability of the temporary mute function.	ON	0:OFF,1:ON	Clearance warning ECU assembly

Sensor

Tester Display	Description	Default	Setting	ECU
Sensor Condition N	Makes the front sensors available when the shift lever is in N.	Avail	0:Not Avail,1:Avail	Clearance warning ECU assembly

Display

Tester Display	Description	Default	Setting	ECU
Approach Display OFF	Sets whether the display turns off after an obstacle is no longer detected.	Avail	0:Not Avail,1:Avail	Clearance warning ECU assembly
Display Mode	The display mode setting (when the intuitive parking assist system is normal).	All	01:All,11:Undisp	Clearance warning ECU assembly

Clearance Warning ECU Power Source Circuit

Data List / Active Test

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Power Steering System(for Hv Model): Calibration
CALIBRATION TORQUE SENSOR ZERO POINT CALIBRATION (USING TECHSTREAM) NOTICE: Perform torque sensor zero point calibration if any of the following conditions occur: The rack and pinion power steering gear assembly has been replaced. There is a difference in steering effort between turning left and rig ...

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual: Customize Parameters

Clearance Warning ECU Power Source Circuit

Data List / Active Test

See More:

Toyota Avalon (XX50) 2019-2022 Owners Manual

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual